Skip to content

论文arXiv 2611.176386 天前

AI引导机器人原位打印:曲率自适应无线伤口电疗器件制造 ​

本文由 AI 根据公开内容整理,可能有误,请以原文为准:AI-guided robotic in situ fabrication of curvature- and tissue-adaptive wireless bioelectronics(arXiv 2611.17638)

核心内容 ​

针对个性化伤口电疗器件需贴合复杂体表且适应个体几何特征的难题,研究团队开发了AI引导机器人原位打印平台。该系统直接在透明伤口敷料上制造无线电疗设备,并在人体等效前臂模型上完成验证,实现了目标频率25MHz下的谐振运行,确立了从感知、设计到制造的物理AI赋能个性化生物电子制造新范式。

技术架构集成3D视觉相机、六自由度机械臂及直写式打印(DIW),核心突破在于将重建的三维几何信息融入电磁设计。不同于仅用几何数据生成轨迹的传统方法,该方案同时补偿解剖曲率与组织介电负载引起的频偏。经流变学与机电稳定性表征的可打印银浆被用于在曲面聚氨酯敷料上制备多层器件,实验证实了无线传能效率与电场递送性能。

关键看点 ​

  • 感知设计闭环:AI分割伤口尺寸与曲率,将三维几何直接融入接收线圈与叉指电极的电磁设计,补偿几何致频移。
  • 多物理场补偿:突破传统仅依赖几何生成轨迹的局限,同步考量解剖曲率与组织介电负载,确保器件在体谐振精度。
  • 原位制造工艺:采用表征完备的可打印银浆,通过直写式打印在曲面聚氨酯敷料上直接制备多层无线生物电子器件。
  • 仿生验证指标:在人体等效前臂模型上实测介电属性并纳入RF优化,成功实现25MHz目标频率下的稳定谐振工作。

工程与产业观察 ​

该工作展示了具身智能在精密医疗制造中的高阶应用,即从单纯的“轨迹执行”进化为“感知驱动的设计-制造协同”。对于机器人算法工程师而言,其核心价值在于验证了将环境物理属性(如介电常数、曲率)实时反馈至功能设计层的可行性,为未来机器人在非结构化环境下进行功能性原位制造提供了重要的工程参考与技术底座。

英文摘要 (Abstract) ​

Personalized bioelectronic devices for wound therapy require not only conformal fabrication on complex body surfaces but also functional adaptation of their electrical characteristics to individual wound geometries. Here, we present an AI-guided robotic in situ printing platform for fabricating wireless wound electrotherapy devices directly on transparent wound dressings. The system integrates a 3D vision camera, a six-degree-of-freedom robotic arm, direct-ink-writing, and geometry-aware RF design optimization. AI-based wound segmentation is used to determine wound dimensions and local surface curvature, while the reconstructed three-dimensional geometry is incorporated into the electromagnetic design of the receiving coil and interdigitated electrodes. In contrast to conventional approaches that use surface geometry only for trajectory generation, the proposed method accounts for both anatomical curvature and tissue dielectric loading to compensate for geometry-induced shifts in resonant behavior. A printable silver ink was characterized in terms of rheology, dimensional reproducibility, electrical resistance, and electromechanical stability, and was used to fabricate multilayer wireless devices directly on curved polyurethane dressings. Wireless power transfer, impedance characteristics, and electric-field delivery were evaluated experimentally and numerically. Finally, robotic in situ fabrication was demonstrated on an anthropomorphic tissue-equivalent forearm phantom, where the measured dielectric properties of the phantom were incorporated into the RF optimization, enabling resonant operation near the target frequency of 25 MHz. This work establishes a perception-to-design-to-fabrication framework for geometry-adaptive wireless bioelectronics and provides a technological foundation for future physical-AI-enabled manufacturing of personalized on-body electrotherapy devices.

作者:Hiroyuki Tetsuka, Jiaju Ma, Naomi Kumano, Minoru Hirano

基于本页技术方向关联的整机参数、核心零部件、实测报告与同赛道选型横评。

外部来源

本页事实对应的公开页面,以原文为准。(点击将离开本站)

  1. arXiv 2611.17638:AI-guided robotic in situ fabrication of curvature- and tissue-adaptive wireless bioelectronics ↗访问 2026-11-16