Skip to content

论文arXiv 2611.189355 天前

UR5单线性化轨迹规划优化:工作点寻优使目标函数降低38% ​

本文由 AI 根据公开内容整理,可能有误,请以原文为准:Optimal Operating-Point Selection for Single-Linearization Trajectory Planning of Nonlinear Robot Manipulators(arXiv 2611.18935)

核心内容 ​

针对非线性机器人机械臂单线性化轨迹规划中线性化点选取影响性能的问题,研究提出一种离线性能驱动的最优工作点选择方法。该方法将线性化位置作为优化变量,从立方种子轨迹采样候选点并求解有限时域二次规划(QP),通过网格搜索与有界细化筛选使非线性目标最小的点。在三自由度 UR5 机械臂的四组点到点运动测试中,最优归一化工作点分布于 0.325 至 0.935 之间,证实了选择的任务相关性。

实验数据显示,相比表现最佳的传统初始、中点或终点线性化策略,该方法在四项任务中分别使非线性轨迹目标函数降低了 17-18%、21-22%、37-38% 和 7-8%。在引入相同 PID 反馈校正的非线性执行测试中,该性能优势得到进一步确认。结果表明,系统化工作点选择能在维持固定仿射规划模型计算效率的同时,显著提升单线性化轨迹规划精度,为低成本实时控制提供理论支撑。

关键看点 ​

  • 算法机制:将单线性化点作为优化变量,基于种子轨迹采样求解QP,经网格搜索与有界细化确定最优工作点
  • 量化收益:在UR5四组P2P任务中,较传统固定点线性化策略,非线性轨迹目标函数最高降低37-38%
  • 鲁棒验证:最优归一化工作点分布在0.325-0.935区间,且在PID反馈校正下性能优势依然显著
  • 工程价值:在不增加在线计算负担前提下,通过离线寻优大幅提升固定仿射模型的轨迹规划精度

工程与产业观察 ​

该研究解决了单线性化MPC在非线性系统中的模型失配痛点,证明了离线工作点寻优对提升规划精度的有效性。对于算力受限的嵌入式机器人控制器,该方案提供了兼顾实时性与动力学精度的工程范式,对机械臂高速高精作业及具身智能底层控制算法优化具有直接参考价值。

英文摘要 (Abstract) ​

Single-point linearization provides a computationally efficient basis for optimization-based trajectory planning of nonlinear robot manipulators. However, planning performance depends on the selected linearization point. This paper presents an offline performance-driven approach that treats the location of a single linearization as an optimization variable. Candidate operating points are sampled from a common cubic seed trajectory, and each corresponding affine model is used to solve an identical constrained finite-horizon quadratic program (QP). The resulting control sequences are executed on the original nonlinear dynamics, and the operating point minimizing the nonlinear trajectory objective is selected through grid search and bounded refinement. Evaluation on four point-to-point motions of a three-degree-of-freedom UR5 manipulator yields optimal normalized operating-point locations between 0.325 and 0.935, demonstrating trajectory-dependent selection. Compared with the best-performing conventional initial, midpoint, or terminal linearization, the proposed approach reduces the nonlinear trajectory objective by 17-18%, 21-22%, 37-38%, and 7-8% across the four tasks, respectively. Additional nonlinear execution with identical PID feedback correction confirms that the performance advantage persists for a representative task. These results demonstrate that systematic operating-point selection can substantially improve single-linearization trajectory planning while preserving a fixed affine planning model.

作者:Bhanuka Dayawansa, Rohan Munasinghe

基于本页技术方向关联的整机参数、核心零部件、实测报告与同赛道选型横评。

外部来源

本页事实对应的公开页面,以原文为准。(点击将离开本站)

  1. arXiv 2611.18935:Optimal Operating-Point Selection for Single-Linearization Trajectory Planning of Nonlinear Robot Manipulators ↗访问 2026-11-18